Yamaha YFM90RYXJ Owner'S Manual Download

Page: 108 / 132

8-25

TIP

After adjusting the brake lever free play, check the
rear brake shoes for wear.

EBU34014

Drive chain slack

The drive chain slack should be checked before
each ride and adjusted if necessary.

TIP

When checking and adjusting the drive chain
slack, there should be no weight on the ATV and
all tires must be touching the ground.

To check the drive chain slack

1. Place the ATV on a level surface.
2. Move the ATV back and forth to locate the

tightest portion of the drive chain, and then
measure the drive chain slack as shown.

3. If the drive chain slack is incorrect, adjust it as

follows.

To adjust the drive chain slack

1. Loosen the bolts and nuts.

1. Rear brake lever free play adjusting nut

(a)

(b)

Drive chain slack:

24.0–32.0 mm (0.94–1.26 in)

1. Drive chain slack

UBD362E0.book Page 25 Tuesday, January 31, 2017 5:10 PM

Summary of Contents for YFM90RYXJ





































































































































Search results

Summary of Contents for YFM90RYXJ

Reviews:

Related manuals for YFM90RYXJ

Brands by name

Popular brands

Yamaha YFM90RYXJ, Owner'S Manual

Search results

Summary of Contents for YFM90RYXJ

Reviews:

Related manuals for YFM90RYXJ

Brands by name

Popular brands