Yamaha YFM90RYXJ Owner'S Manual Download

Page: 107 / 132

8-24

6. Tighten the upper locknut.

TIP

After adjusting the brake lever free play, check the
front brake shoes for wear.

EBU33782

Adjusting the rear brake lever free play

The rear brake lever free play must be checked
and, if necessary, adjusted at the intervals speci-
fied in the periodic maintenance and lubrication
chart.

The brake lever free play should measure 30.0–
40.0 mm (1.18–1.57 in) as shown. If the free play is
incorrect, adjust it as follows.

Turn the adjusting nut in direction (a) to increase
the brake lever free play, and in direction (b) to de-
crease it.

1. Cable joint

a´

a=a´

1. Rear brake lever free play

UBD362E0.book Page 24 Tuesday, January 31, 2017 5:10 PM

Summary of Contents for YFM90RYXJ





































































































































Search results

Summary of Contents for YFM90RYXJ

Reviews:

Related manuals for YFM90RYXJ

Brands by name

Popular brands

Yamaha YFM90RYXJ, Owner'S Manual

Search results

Summary of Contents for YFM90RYXJ

Reviews:

Related manuals for YFM90RYXJ

Brands by name

Popular brands