Yamaha YFM450FAZ Owner'S Manual Download

Page: 48 / 166

4-21

EBU18962

Front carrier

●

Do not exceed the load limit of 40.0 kg (88 lb) for
the front carrier.

●

Do not exceed the maximum load of 210.0 kg
(463 lb) for the ATV.

EBU18972

Rear carrier

●

Do not exceed the load limit of 80.0 kg (176 lb)
for the rear carrier.

●

Do not exceed the maximum load of 210.0 kg
(463 lb) for the ATV.

EBU19145

Adjusting the front and rear shock ab-
sorber assemblies

The spring preload can be adjusted to suit the rid-
er’s weight and the riding conditions.

WARNING

EWB00400

Always adjust the shock absorber assemblies
on the left and right side to the same setting.
Uneven adjustment can cause poor handling
and loss of stability, which could lead to an ac-
cident.

1. Storage compartment drain plug

1. Storage compartment check hose

U37S61E0.book Page 21 Tuesday, June 2, 2009 10:33 AM

Summary of Contents for YFM450FAZ







































































































































































Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands

Yamaha YFM450FAZ, Owner'S Manual

Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands