Yamaha YFM450FAZ Owner'S Manual Download | Manualshive

Page: 39 / 166

background image

4-12

4

crease the maximum engine power available
and the maximum speed of the ATV, turn the
adjusting screw in direction (b). Do not turn
the adjusting screw out more than 12 mm
(0.47 in) or the throttle cable could be dam-
aged. Always make sure the throttle lever free
play is adjusted to 3.0–5.0 mm (0.12–0.20 in).
(See page 8-37.)

WARNING! Improper ad-

justment of the speed limiter and throttle
could cause throttle cable damage or im-
proper throttle operation. You could lose
control, resulting in an accident.

[EWB00241]

3. Tighten the locknut.

EBU18391

Front brake lever

The front brake lever is located on the right handle-
bar. To apply the front brake, pull the brake lever
toward the handlebar grip.

EBU18442

Brake pedal and rear brake lever

The brake pedal is located on the right side of the
ATV and the rear brake lever is located on the left
handlebar. To apply the rear brake, push down on
the brake pedal or pull the brake lever toward the
handlebar grip.

1. Locknut
2. Adjusting screw

3. No more than 12 mm (0.47 in)

1. Front brake lever

U37S61E0.book Page 12 Tuesday, June 2, 2009 10:33 AM

«
...
37
38
39
40
41
...
»

Summary of Contents for YFM450FAZ







































































































































































Reviews:

No comments

Related manuals for YFM450FAZ

Brand: Kabuto Pages: 25

Brand: LAMAX Pages: 134

Brand: hepco & becker Pages: 5

Multistrada 620

Brand: Ducati Pages: 382

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 96

X-MAX 400 ABS 2018

Brand: Yamaha Pages: 118

Virago XV250T 2004

Brand: Yamaha Pages: 95

Brand: Yamaha Pages: 103

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 176

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands