Yamaha YFM450FAZ Owner'S Manual Download

Page: 147 / 166

8-59

4. Insert a new bulb into the bulb holder, push it

in, and then turn it clockwise until it stops.

5. Install the bulb holder (together with the bulb)

by turning it clockwise.

6. Install the tail/brake light assembly by install-

ing the washers and the nuts.

EBU25651

Removing a wheel

1. Place the ATV on a level surface.
2. Loosen the wheel nuts.

3. Elevate the ATV and place a suitable stand

under the frame.

4. Remove the nuts from the wheel.
5. Remove the wheel.

EBU25701

Installing a wheel

1. Place the ATV on a level surface.
2. Install the wheel and the nuts.

TIP

●

The arrow mark

on the tire must point toward

the rotating direction of the wheel.

1. Tail/brake light bulb holder
2. Tail/brake light bulb

1. Wheel nut

U37S61E0.book Page 59 Tuesday, June 2, 2009 10:33 AM

Summary of Contents for YFM450FAZ







































































































































































Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands

Yamaha YFM450FAZ, Owner'S Manual

Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands