Yamaha YFM450FAZ Owner'S Manual Download

Page: 145 / 166

8-57

7. Install the bulb holder cover and the cover at

the rear of the headlight.

NOTICE:

Make sure

the headlight bulb holder cover is securely
fitted over the bulb holder and seated
properly.

[ECB00671]

8. Adjust the headlight beam if necessary.

EBU25551

Adjusting a headlight beam

NOTICE

ECB00690

It is advisable to have a Yamaha dealer make
this adjustment.

To raise a headlight beam, turn the headlight beam
adjusting screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).

EBU25621

Replacing the tail/brake light bulb

If the tail/brake light bulb burns out, replace it as
follows.

1. Remove the tail/brake light assembly by re-

moving the nuts together with the washers.

1. Headlight beam adjusting screw

U37S61E0.book Page 57 Tuesday, June 2, 2009 10:33 AM

Summary of Contents for YFM450FAZ







































































































































































Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands

Yamaha YFM450FAZ, Owner'S Manual

Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands