Yamaha YFM35RX Owner'S Manual Download

Page: 96 / 134

8-18

will affect carburetor jetting with subsequent
poor performance and possible engine over-
heating.

EBU27701

Cleaning the spark arrester

Select a well-ventilated area free of combustible
materials and make sure the exhaust and muffler
are cool.

1. Remove the bolt.

2. Remove the tailpipe by pulling it out of the

muffler.

3. Tap the tailpipe lightly, and then use a wire

brush to remove any carbon deposits from the
spark arrester portion of the tailpipe and inside
of the tailpipe housing.

4. Insert the tailpipe into the muffler and align the

bolt holes.

5. Install the bolt and tighten it to the specified

torque.

6. Remove the purging bolt.

1. Bolt

1. Tailpipe
2. Spark arrester

Tightening torque:

Tailpipe bolt:

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

U5YT64E0.book Page 18 Monday, April 9, 2007 1:03 PM

Summary of Contents for YFM35RX







































































































































Search results

Summary of Contents for YFM35RX

Reviews:

Related manuals for YFM35RX

Brands by name

Popular brands

Yamaha YFM35RX, Owner'S Manual

Search results

Summary of Contents for YFM35RX

Reviews:

Related manuals for YFM35RX

Brands by name

Popular brands