manualshive.com logo in svg

Yamaha YFM35RX, Owner'S Manual

The Yamaha YFM35RX Owner's Manual is a comprehensive guide for users of this powerful off-road vehicle. This indispensable manual provides detailed instructions, important safety information, and maintenance tips to ensure optimal performance. Download your free manual from our website and unleash the full potential of your Yamaha YFM35RX.

Share
Download
background image

8-42

8

2. Remove the defective bulb by pushing it in

and turning it counterclockwise.

3. Insert a new bulb into the socket, push it in,

and then turn it clockwise until it stops.

4. Install the lens by installing the screws.

CAUTION:

ECB00700

Do not overtighten the screws, otherwise the
lens may break.

EBU25650

Removing a wheel 

1. Loosen the wheel nuts.

2. Elevate the ATV and place a suitable stand

under the frame.

3. Remove the nuts from the wheel.

1. Screw

1. Tail/brake light bulb

1. Wheel nut

U5YT64E0.book  Page 42  Monday, April 9, 2007  1:03 PM

Summary of Contents for YFM35RX







































































































































Reviews:

No comments

Related manuals for YFM35RX

Brands by name

Popular brands

Load more brands