manualshive.com logo in svg

Yamaha YFM35RX, Owner'S Manual

The Yamaha YFM35RX Owner's Manual is a comprehensive guide for users of this powerful off-road vehicle. This indispensable manual provides detailed instructions, important safety information, and maintenance tips to ensure optimal performance. Download your free manual from our website and unleash the full potential of your Yamaha YFM35RX.

Share
Download
background image

8-41

8

6. Install the headlight bulb holder cover at the

rear of the headlight.

CAUTION:

ECB00670

Make sure the headlight bulb holder cover is
securely fitted over the bulb holder and seated
properly.

7. Adjust the headlight beam if necessary.

EBU25560

Adjusting a headlight beam 

CAUTION:

ECB00690

It is advisable to have a Yamaha dealer make
this adjustment.

To raise a headlight beam, turn the adjusting bolt
in direction (a).
To lower a headlight beam, turn the adjusting bolt
in direction (b).

EBU25600

Replacing the tail/brake light bulb 

If the tail/brake light bulb burns out, replace it as
follows.

1. Remove the lens by removing the screws.

1. Headlight beam adjusting bolt

U5YT64E0.book  Page 41  Monday, April 9, 2007  1:03 PM

Summary of Contents for YFM35RX







































































































































Reviews:

No comments

Related manuals for YFM35RX

Brands by name

Popular brands

Load more brands