manualshive.com logo in svg

Yamaha YFM35RX, Owner'S Manual

The Yamaha YFM35RX Owner's Manual is a comprehensive guide for users of this powerful off-road vehicle. This indispensable manual provides detailed instructions, important safety information, and maintenance tips to ensure optimal performance. Download your free manual from our website and unleash the full potential of your Yamaha YFM35RX.

Share
Download
background image

8-32

8

CAUTION:

ECB00560

The drive chain must be lubricated after wash-
ing the ATV or riding in the rain.

1. Clean the drive chain with kerosene and a

small soft brush.

CAUTION:

ECB00570

To prevent damaging the O-rings, do not clean
the drive chain with steam cleaners, high-pres-
sure washers or inappropriate solvents.

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a

special O-ring chain lubricant.

CAUTION:

ECB00580

Do not use engine oil or any other lubricants
for the drive chain, as they may contain sub-
stances that could damage the O-rings.

EBU24900

Checking and lubricating the cables 

The operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.

WARNING

EWB02130

Inspect cables frequently and replace if dam-
aged. Corrosion can result when the cable
sheaths become damaged, and cables can
also become frayed or kinked, which could re-
strict the operation of controls and lead to an
accident or injury.

1. O-ring

Recommended lubricant:

Engine oil

U5YT64E0.book  Page 32  Monday, April 9, 2007  1:03 PM

Summary of Contents for YFM35RX







































































































































Reviews:

No comments

Related manuals for YFM35RX

Brands by name

Popular brands

Load more brands