manualshive.com logo in svg

Yamaha YFM35RX, Owner'S Manual

The Yamaha YFM35RX Owner's Manual is a comprehensive guide for users of this powerful off-road vehicle. This indispensable manual provides detailed instructions, important safety information, and maintenance tips to ensure optimal performance. Download your free manual from our website and unleash the full potential of your Yamaha YFM35RX.

Share
Download
background image

8-25

8

●

Make sure the brakes do not drag.

●

Make sure the brakes are not spongy. All air
must be bled from the brake system.

Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.

EBU24591

Checking the brake pedal position 

The brake pedal position must be checked and, if
necessary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart.
The top of the brake pedal should be positioned
50.2 mm (1.98 in) above the top of the frame as
shown. If the brake pedal is not positioned as spec-
ified, have a Yamaha dealer adjust it.

WARNING

EWB02110

Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:

●

Make sure the brakes operate smoothly and
that the brake pedal position is correct.

●

Make sure the brakes do not drag.

●

Make sure the brakes are not spongy. All air
must be bled from the brake system.

Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.

1. Brake pedal position

U5YT64E0.book  Page 25  Monday, April 9, 2007  1:03 PM

Summary of Contents for YFM35RX







































































































































Reviews:

No comments

Related manuals for YFM35RX

Brands by name

Popular brands

Load more brands