manualshive.com logo in svg

Yamaha YFM350RZ, Owner'S Manual

The Yamaha YFM350RZ Owner's Manual is a comprehensive guide that provides essential information on operating and maintaining this exceptional ATV. Easily downloadable from our website, it is available for free. Visit manualshive.com to access this manual and enjoy hassle-free riding experiences with your Yamaha YFM350RZ.

Share
Download
background image

5-1

5

EBU19201

PRE-OPERATION CHECKS

EBU19224

Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always
follow the inspection and maintenance procedures and schedules described in the Owner’s Manual.

WARNING

EWB00481

Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equip-
ment damage. Do not operate the vehicle if you find any problem. If a problem cannot be corrected
by the procedures provided in this manual, have the vehicle inspected by a Yamaha dealer.

Before using this vehicle, check the following points:

ITEM

ROUTINE

PAGE

Fuel

• Check fuel level in fuel tank, and add recommended fuel if neces-

sary.

• Check fuel line for leakage. Correct if necessary.

4-8, 5-3

Engine oil

• Check oil level in engine, and add recommended oil to specified lev-

el if necessary.

• Check ATV for oil leakage. Correct if necessary.

5-3, 8-11

Front brake

• Check operation. If soft or spongy, have Yamaha dealer bleed hy-

draulic system.

• Check brake pads for wear, and replace if necessary.
• Check brake fluid level in reservoir, and add recommended brake 

fluid to specified level if necessary.

• Check hydraulic system for leakage. Correct if necessary.

5-3, 8-22, 8-23, 8-25

U1BS60E0.book  Page 1  Thursday, April 16, 2009  4:11 PM

Summary of Contents for YFM350RZ











































































































































Reviews:

No comments

Related manuals for YFM350RZ

Brands by name

Popular brands

Load more brands