Yamaha YFM350RZ Page 129 Owner'S Manual Download

Page: 129 / 138

10-1

EBU25960

SPECIFICATIONS

Dimensions:

Overall length:

1780 mm (70.1 in)

Overall width:

1095 mm (43.1 in)

Overall height:

1080 mm (42.5 in)

Seat height:

820 mm (32.3 in)

Wheelbase:

1210 mm (47.6 in)

Ground clearance:

115 mm (4.5 in)

Minimum turning radius:

3100 mm (122 in)

Weight:

With oil and fuel:

180.0 kg (397 lb)

Noise and vibration level:

Noise level (77/311/EEC):

YFM35RZ 84.3 dB(A)

Vibration on seat (EN1032, ISO5008):

YFM35RZ Will not exceed 0.5 m/s²

Vibration on handlebar (EN1032, ISO5008):

YFM35RZ Will not exceed 2.5 m/s²

Engine:

Engine type:

Air cooled 4-stroke, SOHC

Cylinder arrangement:

Forward-inclined single cylinder

Displacement:

349 cm³

Bore

stroke:

83.0

64.5 mm (3.27

2.54 in)

Compression ratio:

9.20 :1

Starting system:

Electric starter

Lubrication system:

Wet sump

Engine oil:

Recommended brand:

YAMALUBE

U1BS60E0.book Page 1 Thursday, April 16, 2009 4:11 PM

Summary of Contents for YFM350RZ











































































































































Search results

Summary of Contents for YFM350RZ

Reviews:

Related manuals for YFM350RZ

Brands by name

Popular brands

Yamaha YFM350RZ, Owner'S Manual

Search results

Summary of Contents for YFM350RZ

Reviews:

Related manuals for YFM350RZ

Brands by name

Popular brands