manualshive.com logo in svg

Yamaha YFM350RZ, Owner'S Manual

The Yamaha YFM350RZ Owner's Manual is a comprehensive guide that provides essential information on operating and maintaining this exceptional ATV. Easily downloadable from our website, it is available for free. Visit manualshive.com to access this manual and enjoy hassle-free riding experiences with your Yamaha YFM350RZ.

Share
Download
background image

8-29

8

2. To increase the clutch lever free play, turn the

adjusting bolt at the clutch lever in direction
(a), and to decrease it, turn the bolt in direction
(b).

3. Tighten the locknut at the clutch lever.

If the specified free play cannot be obtained,
proceed with the following steps.

4. Loosen the locknut at the clutch lever.
5. Fully turn the adjusting bolt at the clutch lever

in direction (a) to loosen the clutch cable.

6. Loosen the locknut at the crankcase.
7. To increase the clutch lever free play, turn the

adjusting nut at the crankcase in direction (a),
and to decrease it, turn the nut in direction (b).

8. Tighten the locknut at the crankcase and the

clutch lever.

TIP

If the specified free play cannot be obtained as de-
scribed above or if the clutch does not operate cor-
rectly, have a Yamaha dealer check the internal
clutch mechanism.

EBU24844

Drive chain slack 

The drive chain slack should be checked before
each ride and adjusted if necessary.

To check the drive chain slack

1. Place the ATV on a level surface.

TIP

When checking and adjusting the drive chain
slack, there should be no weight on the ATV and
all tires must be touching the ground.

2. Move the ATV back and forth to locate the

tightest portion of the drive chain, and then
measure the drive chain slack as shown.

1. Locknut
2. Clutch lever free play adjusting nut (crankcase)

Drive chain slack:

25.0–35.0 mm (0.98–1.38 in)

U1BS60E0.book  Page 29  Thursday, April 16, 2009  4:11 PM

Summary of Contents for YFM350RZ











































































































































Reviews:

No comments

Related manuals for YFM350RZ

Brands by name

Popular brands

Load more brands