Yamaha YFM350RB Owner'S Manual Download | Manualshive

Page: 32 / 140

background image

4-7

4

WARNING

EWB00220

●

Always set the parking brake before starting
the engine. The ATV could start moving un-
expectedly if the parking brake is not ap-
plied. This could cause loss of control or a
collision.

●

Always be sure you have released the park-
ing brake before you begin to ride. The brake
could overheat if you ride the ATV without re-
leasing the parking brake. You could lose
braking performance which could cause an
accident. You could also wear out the brakes
prematurely.

EBU18530

Shift pedal

This ATV is equipped with a constant-mesh 6-
speed transmission. The shift pedal is located on
the left side of the engine and is used in combina-
tion with the clutch when shifting.

EBU18571

Drive select lever

The drive select lever is used for driving the ATV
either forward or in reverse. See the “Operating the
drive select lever and driving in reverse” section on
page 6-3 for the drive select lever operation.

1. Shift pedal

U1BS62E0.book Page 7 Monday, April 18, 2011 6:43 PM

«
...
30
31
32
33
34
...
»

Summary of Contents for YFM350RB













































































































































Reviews:

No comments

Related manuals for YFM350RB

Brand: Yamaha Pages: 342

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands