background image

YCH7018  YCH6018  YCHS7018 YCHS7006  Owner’s Manual•

7

Assembly Procedure

Attaching the Sound Tubes

Install the sound tubes with the damper released.

1.

Put the sound tubes on a stable, flat, level 
surface.

To prevent damage to the tubes, place a soft cloth on 
the floor where the tubes will be placed.

2.

Remove the protective film that was applied 
to the sound tube surface.

3.

Hook both end balls of the wire in the 
grooves of the hanger.

At this time, turn the note name toward the player.

Replacing the Wire

1.

Hold the sound tube while being careful not 
to contact other sound tubes and stand, 
detach the end balls from the grooves of the 
hanger, and then remove the sound tube.

2.

Put the sound tubes on a stable, flat, level 
surface.

To prevent damage to the tubes, place a soft cloth on 
the floor where the tubes will be placed.

3.

Remove the wire caps.

When removing the wire cap, pass the wire through 
the slit of the wire cap.

4.

Replace the wire.

5.

Attach the wire caps to the sound tube.

The wire is structured by multiple strands of thin 
metal wires. When a thin metal wire is cut, replace 
the wire with a wire which is not damaged. If the 
wire is broken, the sound tube might fall, and possi-
bly causing injury.

NOTE

• Replace the wire cap if it is damaged. If you keep using the 

damaged wire cap, the wire will be easily damaged. Please 
contact qualified Yamaha service personnel about the wire cap 
(sold separately) for replacement.

• Since the wire caps are very small and can be easily lost, be 

careful when handling them.

End ball

End ball

Hanger

Hanger

Note name

Accidental tone side

YCH7018, YCH6018, YCHS7018

Generally, arrange the sound tubes as shown 
below. The places filled with gray are not used.

Natural 

tone side

Long tube

Short tube

End ball

End ball

Wire cap

Slit

Wire

Wire cap

Slit

Wire

C

AUTION

Summary of Contents for YCH7018











Reviews: