manualshive.com logo in svg

Yamaha XVS950CU 2014, Service Manual, Page: 286 / 580

Share
Download
Yamaha XVS950CU 2014 Service Manual Download Page 286

BELT DRIVE

4-95

EAS23520

REMOVING THE DRIVE BELT AND DRIVE 
PULLEY

1. Straighten the drive pulley nut ribs “a”.

2. Loosen:

• Drive pulley nut

TIP

When loosening the drive pulley nut, press down 
on the brake pedal so the drive pulley does not 
move.

3. Remove:

• Drive belt

TIP

Push the rear wheel forward and remove the 
drive belt from the rear wheel pulley. Refer to 
“ADJUSTING THE DRIVE BELT SLACK” on 
page 3-18.

EAS23530

CHECKING THE DRIVE BELT

1. Clean:

• Drive belt

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Wipe the drive belt with a clean cloth.
b. Put the drive belt in a mixture of mild deter-

gent and water. Then, remove any dirt from 
the drive belt.

c. Remove the drive belt from the mixture and 

rinse it off with clean water. Then, let the drive 
belt thoroughly dry.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

2. Check:

• Drive belt

NOTICE

ECA1TP1030

• To protect the drive belt from damage, han-

dle it with care.

• The drive belt can not be bent smaller than 

125 mm (4.92 in) “a”.

• The removed drive belt can not be twisted 

inside out.

3. Check:

• Drive pulley
• Rear wheel pulley

Bent teeth 

→

 Replace the drive belt and pul-

leys as a set.

EAS23540

INSTALLING THE DRIVE BELT AND DRIVE 
PULLEY

1. Install:

• Drive belt

NOTICE

ECA1TP1031

Align the mark of the drive belt with the 
progress direction “A”.
Do not twist the drive belt when installing it.

2. Install:

• Washer

• Drive pulley nut 

TIP

Install the washer with its “OUT” mark facing out-
ward.

3. Tighten:

• Drive pulley nut

a

A

New

Summary of Contents for XVS950CU 2014





































































































































































































































































































































































































































































































































































































Reviews:

No comments