Yamaha XVS65A Owner'S Manual Download

Page: 81 / 98

SPECIFICATIONS

9-1

Dimensions:

Overall length:

2340 mm (92.1 in)

Overall width:

880 mm (34.6 in)

Overall height:

1075 mm (42.3 in)

Seat height:

695 mm (27.4 in)

Wheelbase:

1610 mm (63.4 in)

Ground clearance:

140 mm (5.51 in)

Minimum turning radius:

3100 mm (122.0 in)

Weight:

With oil and fuel:

XVS65A 233 kg (514 lb)
XVS65AC 235 kg (518 lb)

Engine:

Engine type:

Air cooled 4-stroke, SOHC

Cylinder arrangement:

V-type 2-cylinder

Displacement:

649 cm³

Bore

stroke:

81.0

63.0 mm (3.19

2.48 in)

Compression ratio:

9.00 :1

Starting system:

Electric starter

Lubrication system:

Wet sump

Engine oil:

Recommended brand:

YAMALUBE

Type:

SAE 10W-30, 10W-40, 10W-50, 15W-40,
20W-40 or 20W-50

Recommended engine oil grade:

API service SG type or higher, JASO
standard MA

Engine oil quantity:

Without oil filter element replacement:

2.60 L (2.75 US qt, 2.29 Imp.qt)

With oil filter element replacement:

2.80 L (2.96 US qt, 2.46 Imp.qt)

Final gear oil:

Type:

SAE 80 API GL-4 Hypoid gear oil

Quantity:

0.19 L (0.20 US qt, 0.17 Imp.qt)

Air filter:

Air filter element:

Dry element

Fuel:

Recommended fuel:

Unleaded gasoline only

Fuel tank capacity:

16.0 L (4.23 US gal, 3.52 Imp.gal)

Fuel reserve amount:

3.0 L (0.79 US gal, 0.66 Imp.gal)

Carburetor:

Type

quantity:

BDS28 x 2

Spark plug(s):

Manufacturer/model:

NGK/DPR7EA-9

Manufacturer/model:

DENSO/X22EPR-U9

Spark plug gap:

0.8–0.9 mm (0.031–0.035 in)

Clutch:

Clutch type:

Wet, multiple-disc

Transmission:

Primary reduction system:

Spur gear

Primary reduction ratio:

68/38 (1.789)

Secondary reduction system:

Shaft drive

Secondary reduction ratio:

19/18

32/11 (3.071)

Transmission type:

Constant mesh 5-speed

Operation:

Left foot operation

–20 –10 0

10 20 30 40 50 ˚C

10 30 50 70 90 110

130 ˚F

SAE 10W-30

SAE 15W-40

SAE 20W-40

SAE 20W-50

SAE 10W-40

SAE 10W-50

U1BF11E0.book Page 1 Tuesday, April 13, 2010 9:28 AM

Summary of Contents for XVS65A



































































































Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands

Yamaha XVS65A, Owner'S Manual

Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands