Yamaha XVS65A Owner'S Manual Download | Manualshive

Page: 60 / 98

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-22

7

●

A soft or spongy feeling in the
brake lever can indicate the
presence of air in the hydraulic
system. If there is air in the hy-
draulic system, have a Yamaha
dealer bleed the system before
operating the motorcycle. Air in
the hydraulic system will dimin-
ish the braking performance,
which may result in loss of con-
trol and an accident.

EAU22231

Adjusting the brake pedal po-
sition and free play

WARNING

EWA10670

It is advisable to have a Yamaha
dealer make these adjustments.

TIP

The brake pedal position should be ad-
justed before adjusting the brake pedal
free play.

Brake pedal position

The brake pedal should be positioned
approximately 82.0 mm (3.23 in) above
the top of the footrest as shown. Peri-
odically check the brake pedal position
and, if necessary, adjust it as follows.

1. Loosen the locknut at the brake

pedal.

2. To raise the brake pedal, turn the

adjusting bolt in direction (a). To
lower the brake pedal, turn the ad-
justing bolt in direction (b).

3. Tighten the locknut.

1. Distance between brake pedal and footrest

2. Brake pedal free play

1. Locknut
2. Brake pedal position adjusting bolt

U1BF11E0.book Page 22 Tuesday, April 13, 2010 9:28 AM

«
...
58
59
60
61
62
...
»

Summary of Contents for XVS65A



































































































Reviews:

No comments

Related manuals for XVS65A

Brand: Yamaha Pages: 94

Brand: KEEWAY Pages: 164

Trekker Dolomiti

Brand: GIVI Pages: 24

Brand: Apollo Pages: 92

Stelvio 1200 MY11 2011

Brand: MOTO GUZZI Pages: 385

Brand: Thunderbike Pages: 7

Brand: DYNATEK Pages: 6

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 4

VIKING 2450 Series

Brand: Lincoln Electric Pages: 48

BLITZ 9-13 Visor

Brand: Fubag Pages: 17

Brand: R&G Pages: 2

Brand: Aosom Pages: 13

VarioProtect XXL-W-2 TC

Brand: Schweißkraft Pages: 16

Ride-On Motorcycle

Brand: Rovo Kids Pages: 17

Brand: Tomberlin Pages: 107

Brand: Honda Pages: 43

Brand: KTM Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands