Yamaha XVS65A Owner'S Manual Download

Page: 50 / 98

PERIODIC MAINTENANCE AND ADJUSTMENT

7-12

EAU19745

Engine oil and oil filter ele-
ment

The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter ele-
ment replaced at the intervals specified
in the periodic maintenance and lubri-
cation chart.

To check the engine oil level

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion. A slight tilt to the side can
result in a false reading.

2. Start the engine, warm it up for

several minutes, and then turn it
off.

3. Wait a few minutes until the oil set-

tles, and then check the oil level
through the check window located
at the bottom-left side of the crank-
case.

TIP

The engine oil should be between the
minimum and maximum level marks.

4. If the engine oil is at or below the

minimum level mark, add sufficient
oil of the recommended type to
raise it to the correct level.

To change the engine oil (with or
without oil filter element replace-
ment)

1. Start the engine, warm it up for

several minutes, and then turn it
off.

2. Place an oil pan under the engine

to collect the used oil.

3. Remove the engine oil filler cap,

the engine oil drain bolt and its
gasket to drain the oil from the
crankcase.

TIP

Skip steps 4–7 if the oil filter element is
not being replaced.

4. Remove the outer and inner oil fil-

ter element covers by removing
the bolts.

1. Engine oil level check window
2. Maximum level mark

3. Minimum level mark

1. Engine oil filler cap
2. Engine oil drain bolt

3. Gasket

U1BF11E0.book Page 12 Tuesday, April 13, 2010 9:28 AM

Summary of Contents for XVS65A



































































































Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands

Yamaha XVS65A, Owner'S Manual

Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands