Yamaha XVS65A Owner'S Manual Download | Manualshive

Page: 35 / 98

background image

OPERATION AND IMPORTANT RIDING POINTS

6-1

6

EAU15951

Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.

WARNING

EWA10271

Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which could cause an accident
or injury.

EAU15999

Starting and warming up a
cold engine

In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:

●

The transmission is in the neutral
position.

●

The transmission is in gear with
the clutch lever pulled and the
sidestand up.
See page 4-14 for more informa-
tion.

1. Turn the fuel cock lever to “ON”.
2. Turn the key to “ON” and make

sure that the engine stop switch is
set to “

”.

3. Shift the transmission into the neu-

tral position. The neutral indicator
light should come on. If not, ask a
Yamaha dealer to check the elec-
trical circuit.

4. Turn the starter (choke) on and

completely close the throttle. (See
page 4-9.)

5. Start the engine by pushing the

start switch.

If the engine fails to start, release
the start switch, wait a few sec-
onds, and then try again. Each
starting attempt should be as short
as possible to preserve the bat-
tery. Do not crank the engine more
than 10 seconds on any one at-
tempt.

6. After starting the engine, move the

starter (choke) back halfway.

7. When the engine is warm, turn the

starter (choke) off.

TIP

The engine is warm when it responds
quickly to the throttle with the starter
(choke) turned off. To avoid the possi-
bility of excessive exhaust emissions,
never leave the starter (choke) on long-
er than necessary. The time necessary
for starter (choke) use depends upon
the ambient temperature. Tempera-
tures above 10 °C (50 °F) require about
7 seconds of starter (choke) use and
temperatures below 10 °C (50 °F) re-
quire about 35 seconds with the starter
(choke) turned on, then about 2.5 min-
utes with the starter (choke) in the half-
way position.

U1BF11E0.book Page 1 Tuesday, April 13, 2010 9:28 AM

«
...
33
34
35
36
37
...
»

Summary of Contents for XVS65A



































































































Reviews:

No comments

Related manuals for XVS65A

Brand: Big Bike Parts Pages: 2

Brand: Honda Pages: 158

Brand: LAZER Pages: 11

Brand: GAS GAS Pages: 131

Brand: TVS Pages: 48

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

XVS950A Midnight Star

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 327

Brand: Dakota Digital Pages: 4

Brand: Beta Pages: 41

Brand: KEDO Pages: 3

Brand: hepco & becker Pages: 3

Brand: Honda Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands