Yamaha XT660R Owner'S Manual Download Page 54 | Manualshive

Page: 54 / 92

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-16

6

16. Check the coolant level in the res-

ervoir. If necessary, remove the
coolant reservoir cap, add coolant
to the maximum level mark, and
then install the cap.

17. Start the engine, and then check

the vehicle for coolant leakage. If
coolant is leaking, have a Yamaha
dealer check the cooling system.

18. Install the cowling, the panel and

the seat.

EAUM1833

Replacing the air filter element
and cleaning the check hose

The air filter element should be re-
placed at the intervals specified in the
periodic maintenance and lubrication
chart. Replace the air filter element
more frequently if you are riding in un-
usually wet or dusty areas. In addition,
the air filter check hose must be fre-
quently checked and cleaned if neces-
sary.

To replace the air filter element

1. Remove the seat. (See page

2. Remove panel B. (See page 6-5.)
3. Remove the air filter case cover by

removing the screws.

4. Pull the air filter element out.
5. Insert a new air filter element into

the air filter case as shown.

1. Air filter case cover
2. Screw

1. Air filter element

U5VKE1E0.book Page 16 Tuesday, July 18, 2006 1:00 PM

«
...
52
53
54
55
56
...
»

Summary of Contents for XT660R





























































































Reviews:

No comments

Related manuals for XT660R

Brand: AGV Pages: 45

Brand: Nuviz Pages: 46

Brand: Yamaha Pages: 120

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 2

Brand: hepco & becker Pages: 2

Brand: SUR-RON Pages: 37

Brand: BMS Pages: 11

Siegen Tools S01001.V3

Brand: Sealey Pages: 4

Brand: Deco Pages: 40

Brand: Benelli Pages: 47

Tornado Naked Tre 1130

Brand: Benelli Pages: 55

sprite-barracuda

Brand: Benelli Pages: 64

Brand: Abus Pages: 35

Brand: Gazzini Pages: 35

Brand: Harbor Freight Tools Pages: 9

Brand: Laverda Pages: 151

Brand: AFX Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands