Yamaha XT660R Owner'S Manual Download | Manualshive

Page: 18 / 92

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-3

3

To unlock the steering

Push the key in, and then turn it to
“OFF” while still pushing it.

WARNING

EWA10060

Never turn the key to “OFF” or
“LOCK” while the vehicle is moving,
otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident. Make
sure that the vehicle is stopped be-
fore turning the key to “OFF” or
“LOCK”.

EAU33001

(Parking)

The steering is locked, and the taillight
and auxiliary light are on. The hazard
lights and turn signal lights can be
turned on, but all other electrical sys-
tems are off. The key can be removed.
The steering must be locked before the
key can be turned to “

”.

CAUTION:

ECA11020

Do not use the parking position for
an extended length of time, other-
wise the battery may discharge.

EAU11003

Indicator and warning lights

EAU11020

Turn signal indicator light “

”

This indicator light flashes when the
turn signal switch is pushed to the left or
right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

1. Push.
2. Turn.

1. Engine trouble warning light “

”

2. Turn signal indicator light “

”

3. Fuel level warning light “

”

4. High beam indicator light “

”

5. Neutral indicator light “

”

6. Coolant temperature warning light “

”

7. Immobilizer system indicator light “

”

U5VKE1E0.book Page 3 Tuesday, July 18, 2006 1:00 PM

«
...
16
17
18
19
20
...
»

Summary of Contents for XT660R





























































































Reviews:

No comments

Related manuals for XT660R

Brand: Caberg Pages: 3

Brand: Caberg Pages: 2

Brand: KAYO MOTOR Pages: 84

Brand: Öhlins Pages: 8

Brand: NEO TOOLS Pages: 8

Brand: Denali Pages: 5

Brand: Honda Pages: 556

Brand: MSD Ignition Pages: 16

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 63

Brand: Yamaha Pages: 78

Brand: Yamaha Pages: 94

Star XV1900AE 2013

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 99

Brand: Yamaha Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands