manualshive.com logo in svg

Yamaha XMAX 2022, Owner'S Manual, Page: 93 / 122

Share
Download
Yamaha XMAX 2022 Owner'S Manual Download Page 93

Perio

d

ic maintenance an

d

 a

d

justment

8-31

8

3. Turn the main switch on and turn

on the electrical circuit in question
to check if the device operates.

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

EAUN2261

Vehicle li

g

hts

This model is equipped with LED lights
for headlights, auxiliary lights and
brake/tail light. If a light does not come
on, check the fuse and then have a
Yamaha dealer check the vehicle.

NOTICE

ECA16581

Do not affix any type of tinte

d

 film or

stickers to the hea

d

li

g

ht lens.

EAU43006

Replacin

g

 a turn si

g

nal li

g

ht 

b

ul

b

1. Remove the turn signal light unit

by removing the screw.

2. Remove the turn signal light bulb

socket (together with the bulb) by
turning it counterclockwise.

1. Headlight (low beam)
2. Headlight (high beam)
3. Auxiliary light

2

1

3

3

1. Turn signal light lens
2. Screw

1

2

UB5X10E0.book  Page 31  Thursday, May 27, 2021  8:55 AM

Summary of Contents for XMAX 2022



























































































































Reviews:

No comments