Yamaha XMAX 2022 Owner'S Manual Download Page 92 | Manualshive

Page: 92 / 122

background image

Perio

d

ic maintenance an

d

a

d

justment

8-30

8

EAU78242

Replacin

g

the fuses

The main fuse and the fuse boxes,
which contain the fuses for the individ-
ual circuits, are located under panel A.
(See page 8-8.)

TIP

To access the main fuse, remove the
starter relay cover as shown.

If a fuse is blown, replace it as follows.

1. Turn the main switch off and turn

off the electrical circuit in ques-
tion.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

WARNING! Do not

use a fuse of a hi

g

her ampera

g

e

ratin

g

than recommen

d

e

d

to

avoi

d

causin

g

extensive

d

am-

a

g

e to the electrical system an

d

possi

b

ly a fire.

[EWA15132]

1. Fuse box
2. Main fuse
3. Spare main fuse
4. Starter relay cover

1

2

3

4

1. Signaling system fuse 2
2. Signaling system fuse
3. ABS control unit fuse
4. Main fuse 2
5. Radiator fan motor fuse
6. Backup fuse
7. Spare fuse
8. ABS motor fuse
9. ABS solenoid fuse
10.Turn signal light and hazard fuse
11.Terminal fuse 1
12.Answer back fuse

1

2

3

4

5

6

7

8

9

10

11
12

7

Specifie

d

fuses:

Main fuse:

20.0 A

Main fuse 2:

10.0 A

Terminal fuse 1:

2.0 A

Signaling system fuse:

10.0 A

Signaling system fuse 2:

7.5 A

Radiator fan motor fuse:

7.5 A

Backup fuse:

15.0 A

Turn signal light and hazard fuse:

15.0 A

ABS control unit fuse:

7.5 A

ABS motor fuse:

30.0 A

ABS solenoid fuse:

15.0 A

Answer back fuse:

2.0 A

UB5X10E0.book Page 30 Thursday, May 27, 2021 8:55 AM

«
...
90
91
92
93
94
...
»

Summary of Contents for XMAX 2022



























































































































Reviews:

No comments

Related manuals for XMAX 2022

Brand: Insportline Pages: 19

990D0-44G00-ALM

Brand: Suzuki Pages: 24

Brand: Rivco Pages: 5

Brand: Pandora Pages: 56

SPORTTOURING ST4S

Brand: Ducati Pages: 313

690 SMC R 2016 Series

Brand: KTM Pages: 18

Brand: Yamaha Pages: 164

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 80

Brand: DYNATEK Pages: 11

Brand: GPX Pages: 44

Brand: Shad Pages: 12

Brand: Shad Pages: 2

KIT TOPMASTER S0BN11ST

Brand: Shad Pages: 2

KIT TOPMASTER S0SV69ST

Brand: Shad Pages: 2

KIT TOPMASTER S0GL69ST

Brand: Shad Pages: 2

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands