Yamaha XMAX 2022 Owner'S Manual Download Page 46 | Manualshive

Page: 46 / 122

background image

Instrument an

d

control functions

5-16

5

WARNING

EWA11092

Make sure that the fuel tank cap is
properly close

d

after fillin

g

fuel.

Leakin

g

fuel is a fire hazar

d

.

EAU13213

Fuel

Make sure there is sufficient gasoline in
the tank.

WARNING

EWA10882

Gasoline an

d

g

asoline vapors are

extremely flamma

b

le. To avoi

d

fires

an

d

explosions an

d

to re

d

uce the

risk of injury when refuelin

g

, follow

these instructions.

1. Before refueling, turn off the en-

gine and be sure that no one is sit-
ting on the vehicle. Never refuel
while smoking, or while in the vi-
cinity of sparks, open flames, or
other sources of ignition such as
the pilot lights of water heaters
and clothes dryers.

2. Do not overfill the fuel tank. Stop

filling when the fuel reaches the
bottom of the filler tube. Because
fuel expands when it heats up,
heat from the engine or the sun
can cause fuel to spill out of the
fuel tank.

3. Wipe up any spilled fuel immedi-

ately.

NOTICE:

Imme

d

iately

wipe off spille

d

fuel with a clean,

d

ry, soft cloth, since fuel may

d

eteriorate painte

d

surfaces or

plastic parts.

[ECA10072]

4. Be sure to securely close the fuel

tank cap.

WARNING

EWA15152

Gasoline is poisonous an

d

can

cause injury or

d

eath. Han

d

le

g

aso-

line with care. Never siphon

g

asoline

b

y mouth. If you shoul

d

swallow

some

g

asoline or inhale a lot of

g

as-

oline vapor, or

g

et some

g

asoline in

your eyes, see your

d

octor imme

d

i-

1. Fuel tank filler tube
2. Maximum fuel level

1

2

UB5X10E0.book Page 16 Thursday, May 27, 2021 8:55 AM

«
...
44
45
46
47
48
...
»

Summary of Contents for XMAX 2022



























































































































Reviews:

No comments

Related manuals for XMAX 2022

Brand: X-lite Pages: 5

Brand: Yamaha Pages: 287

Brand: Ducati Pages: 128

Mambo Evo PURE CARBON

Brand: LAZER Pages: 13

Brand: Kabuto Pages: 6

Brand: GAS GAS Pages: 32

Brand: hepco & becker Pages: 3

Brand: DYNATEK Pages: 4

Brand: Yamaha Pages: 400

Brand: hepco & becker Pages: 2

Brand: Kinroad Pages: 26

Brand: TERMOSCUD Pages: 8

Brand: Bike Shield Pages: 4

XTRA - RAPTOR 1000

Brand: Cagiva Pages: 142

Brand: APRILIA Pages: 170

Brand: MT Helmets Pages: 9

Brand: Brixton Pages: 148

Vertex Best Duo

Brand: Petzl Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands