Yamaha XMAX 2022 Owner'S Manual Download Page 45

Page: 45 / 122

Instrument an

control functions

5-15

If the traction control system automat-
ically disables, try resetting it as fol-
lows.

1. Stop the vehicle and turn it off

completely.

2. Wait a few seconds and then turn

the vehicle power on.

3. The “

” indicator light should

turn off and the system be en-
abled.

TIP

If the “

” indicator light remains on af-

ter resetting, the vehicle may still be
ridden; however, have a Yamaha deal-
er check the vehicle as soon as possi-
ble.

4. Have a Yamaha dealer check the

vehicle and turn off the “

”

warning light.

EAU78502

Fuel tank cap

To remove the fuel tank cap

1. Turn the main switch to “

” to

open the fuel tank cap lid.

2. Turn the fuel tank cap counter-

clockwise until the release
mark “ ” aligns with “

”, and

then pull the cap off.

To install the fuel tank cap

1. Insert the fuel tank cap onto the

tank opening and turn it clockwise
until the install mark “

” aligns

with “

”.

2. Close the fuel tank cap lid.

1. Fuel tank cap lid

1. Fuel tank cap
2. Release mark “ ”

1. Install mark “

”

UB5X10E0.book Page 15 Thursday, May 27, 2021 8:55 AM

Summary of Contents for XMAX 2022



























































































































Search results

Summary of Contents for XMAX 2022

Reviews:

Related manuals for XMAX 2022

Brands by name

Popular brands

Yamaha XMAX 2022, Owner'S Manual

Search results

Summary of Contents for XMAX 2022

Reviews:

Related manuals for XMAX 2022

Brands by name

Popular brands