background image

STARTING AND BREAK-IN

1-33

WARNING

EWA19030

Since exhaust gas contains harmful ingredi-

ents, do not start or warm it up at an illventi-

lated place or a closed narrow place.

5. To stop the engine, push the engine stop

switch “1”.

TIP

Continue pushing the engine stop switch till the
engine comes to a full stop.

EAM30197

STARTING A WARM ENGINE

Follow the same procedure as for starting a cold
engine with the exception that the starter is not
required when the engine is warm.

TIP

If the engine fail to start, fully open the throttle
grip and push the start switch few seconds to
clear the engine of the rich air-fuel mixture re-
tained in it.

EAM30198

BREAK-IN PROCEDURES

A break-in is important so that rotating portion,
sliding surfaces, and mounted areas may fit one
another, and that the rider may become accus-
tomed to the machine.

NOTICE

ECA25811

Before running, do maintenance on the air

filter element.

1. After warming up the engine, drive it for about

20 minutes at a throttle opening of 1/2 or less.

TIP

This model is equipped with an engine auto-stop
system. The engine stops automatically if left
idling for 7 minutes. If the engine stops, push the
start switch to restart the engine.

2. Make a pit stop, and check mounted areas for

looseness, oil leaks, or other problems.

3. Then, drive it for about 40 minutes at a throt-

tle opening of 3/4 or less.

4. Make a pit stop again, and thoroughly check

mounted areas for looseness, oil leaks, or
other problems. Thorough checks and ad-
justments are required in particular for stretch
of cables, free play of the brake, stretch of the
drive chain, looseness of the spoke, and so
on.

NOTICE

ECA25821

After a break-in or after each race, always

check the points shown in “TORQUE-

CHECK POINTS” for tightening torques and

retighten them.

Also when the following parts are replaced, a

break-in is required.

• Cylinder and Crankshaft: A break-in is re-

quired for about an hour.

• Piston, Piston ring, Valve, Camshaft, and

Gear: A break-in is required for about 30

minutes at a throttle opening of 1/2 or less.

Observe the condition of the engine carefully

during a break-in.

For checkpoints for a break-in, see “MAIN-

TENANCE AFTER BREAK-IN”. If any prob-

lem is found, immediately stop the engine

and make a checkup.

EAM30623

SHIFTING

The shift pedal “1” has adopted a method of 1
down & 4 ups (press-down & kick-ups).
Press it down for N (neutral) to 1st, and kick it up
for 2nd to 5th.

1

1

1

Summary of Contents for WR450FN 2022



















































































































































































































































































































































































































Reviews: