Yamaha WR250X Page 89 Owner'S Manual Download

Page: 89 / 112

PERIODIC MAINTENANCE AND ADJUSTMENT

7-44

EAU42131

Troubleshooting charts

Starting problems or poor engine performance

Check the fuel level in
the fuel tank.

1. Fuel

There is enough fuel.

There is no fuel.

Check the compression.

Supply fuel.

The engine does not start.
Check the compression.

Operate the electric starter.

2. Compression

There is compression.

There is no compression.

Check the ignition.

Have a Yamaha dealer
check the vehicle.

Remove the spark plug
and check the electrodes.

3. Ignition

Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.

Have a Yamaha dealer check the vehicle.

The engine does not start.
Have a Yamaha dealer
check the vehicle.

The engine does not start.
Check the battery.

Operate the electric starter.

4. Battery

The engine turns over
quickly.

The engine turns over
slowly.

The battery is good.

Check the battery lead connections,
and charge the battery if necessary.

Dry

Wet

Operate the electric starter.

U32C15E0.book Page 44 Tuesday, July 14, 2009 11:43 AM

Summary of Contents for WR250X

















































































































Search results

Summary of Contents for WR250X

Reviews:

Related manuals for WR250X

Brands by name

Popular brands

Yamaha WR250X, Owner'S Manual

Search results

Summary of Contents for WR250X

Reviews:

Related manuals for WR250X

Brands by name

Popular brands