manualshive.com logo in svg

Yamaha WR250X, Owner'S Manual, Page: 84 / 112

Share
Download
Yamaha WR250X Owner'S Manual Download Page 84

PERIODIC MAINTENANCE AND ADJUSTMENT

7-39

7

EAU24312

Replacing the license plate 
light bulb 

1. Remove the license plate light unit

by removing the screws.

2. Remove the socket (together with

the bulb) by pulling it out.

3. Remove the burnt-out bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the socket (together with the

bulb) by pushing it in.

6. Install the license plate light unit by

installing the screws.

EAU24350

Supporting the motorcycle 

Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other maintenance
requiring the motorcycle to stand up-
right. Check that the motorcycle is in a
stable and level position before starting
any maintenance. A strong wooden
box can be placed under the engine for
added stability.

To service the front wheel

1. Stabilize the rear of the motorcycle

by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.

2. Raise the front wheel off the

ground by using a motorcycle
stand.

To service the rear wheel

Raise the rear wheel off the ground by
using a motorcycle stand or, if a motor-
cycle stand is not available, by placing

1. Screw

1. License plate light unit

2. License plate light bulb socket

1

1

2

U32C15E0.book  Page 39  Tuesday, July 14, 2009  11:43 AM

Summary of Contents for WR250X

















































































































Reviews:

No comments