manualshive.com logo in svg

Yamaha WR250F 2022, Owner'S Service Manual


Share
Download
background image

CHAIN DRIVE

4-70

EAM30075

REMOVING THE DRIVE CHAIN

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

TIP

Place the vehicle on a maintenance stand so
that the rear wheel is elevated.

2. Remove:

•

Drive chain

TIP

Cut the drive chain with the drive chain cut & riv-
et tool. (Use goods on the market.)

EAM30076

CHECKING THE DRIVE CHAIN

1. Measure:

•

15-link section of the drive chain
Out of specification 

 Replace the drive

chain.

a. Measure the length “a” between the inner

sides of the pins and the length “b” be-
tween the outer sides of the pins on a 15-
link section of the drive chain as shown in
the illustration.

b. Calculate the length “c” of the 15-link sec-

tion of the drive chain using the following
formula.
Drive chain 15-link section length “c” =
(length “a” between pin inner sides +
length “b” between pin outer sides)/2

TIP

•

When measuring a 15-link section of the drive
chain, make sure that the drive chain is taut.

•

Perform this procedure 2–3 times, at a different
location each time.

2. Check:

•

Drive chain
Stiffness 

 Clean, lubricate, or replace.

3. Clean:

•

Drive chain
a. Wipe the drive chain with a clean cloth.
b. Put the drive chain in kerosene and re-

move any remaining dirt.

c. Remove the drive chain from the kerosene

and completely dry it.

NOTICE

ECA19090

• This vehicle has a drive chain with small

rubber O-rings “1” between the drive chain

side plates. Never use high-pressure water

or air, steam, gasoline, certain solvents

(e.g., benzine), or a coarse brush to clean

the drive chain. High-pressure methods

could force dirt or water into the drive

chain’s internals, and solvents will deterio-

rate the O-rings. A coarse brush can also

damage the O-rings. Therefore, use only

kerosene to clean the drive chain.

• Do not soak the drive chain in kerosene for

more than ten minutes, otherwise the O-

rings can be damaged.

15-link length limit

239.3 mm (9.42 in)

Summary of Contents for WR250F 2022





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250F 2022

Cannondale E440 Owner'S Manual preview
E440
Brand: Cannondale Pages: 102
KAYO MOTOR K4 Service Manual preview
K4
Brand: KAYO MOTOR Pages: 74
KAYO MOTO K4 Assembly Manual preview
K4
Brand: KAYO MOTO Pages: 5
Öhlins YA812 Mounting Instructions preview
YA812
Brand: Öhlins Pages: 2
Öhlins YA 314 Mounting Instructions preview
YA 314
Brand: Öhlins Pages: 2
Öhlins TR 538 Mounting Instructions preview
TR 538
Brand: Öhlins Pages: 2
Öhlins ST44 Mounting Instructions preview
ST44
Brand: Öhlins Pages: 2
Öhlins SD195 Mounting Instruction preview
SD195
Brand: Öhlins Pages: 2
Öhlins SD 168 Mounting Instructions preview
SD 168
Brand: Öhlins Pages: 2
Öhlins SD 154 Mounting Instructions preview
SD 154
Brand: Öhlins Pages: 2
Öhlins RS 562 Mounting Instructions preview
RS 562
Brand: Öhlins Pages: 2
Öhlins POF5H00 Mounting Instructions preview
POF5H00
Brand: Öhlins Pages: 2
GBRacing BA12-6-GBR-SET Fitting Instructions preview
BA12-6-GBR-SET
Brand: GBRacing Pages: 2
Happy Trails HTP1-12-7 Quick Start Manual preview
HTP1-12-7
Brand: Happy Trails Pages: 3
Honda st1300/a 2007 Setup Instructions preview
st1300/a 2007
Brand: Honda Pages: 28
RPS Falcon 200 Owner'S Manual preview
Falcon 200
Brand: RPS Pages: 28
Yamaha XV19CSD Owner'S Manual preview
XV19CSD
Brand: Yamaha Pages: 96
Yamaha XV17AWZ Owner'S Manual preview
XV17AWZ
Brand: Yamaha Pages: 110

Brands by name

Popular brands

Load more brands