manualshive.com logo in svg

Yamaha WR250F 2022, Owner'S Service Manual


Share
Download
background image

FRONT BRAKE

4-22

4. Check:

•

Brake fluid level
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-23.

5. Check:

•

Brake lever operation
A softy or spongy feeling 

 Bleed the brake

system.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-25.

EAM30030

REMOVING THE FRONT BRAKE CALIPER

TIP

Before disassembling the brake caliper, drain
the brake fluid from the entire brake system.

1. Remove:

•

Union bolt

•

Copper washer

•

Brake hose

TIP

Put the end of the brake hose into a container
and pump out the brake fluid.

EAM30031

DISASSEMBLING THE FRONT BRAKE 

CALIPER

1. Remove:

•

Brake caliper piston “1”

•

Brake caliper piston seal kit “2”

a. Blow compressed air into the brake hose

joint opening to force out the piston from
the brake caliper.

WARNING

EWA13550

• Cover the brake caliper piston with a rag.

Be careful not to get injured when the pis-

ton is expelled from the brake caliper.

• Never try to pry out the brake caliper pis-

ton.

b. Remove the brake caliper piston dust seal

and the brake caliper piston seal.

EAM30032

CHECKING THE FRONT BRAKE CALIPER

1. Check:

•

Brake caliper piston “1”
Rust/scratches/wear 

 Replace the brake

caliper piston.

•

Brake caliper cylinder “2”
Scratches/wear 

 Replace the brake caliper

assembly.

•

Brake caliper body “3”
Cracks/damage 

 Replace the brake caliper

assembly.

•

Brake fluid delivery passages
(brake caliper body)
Obstruction 

 Blow out with compressed air.

WARNING

EWA19220

When the brake caliper is disassembled, re-

place the brake caliper piston seal and the

brake caliper piston dust seal with new ones.

2. Check:

•

Brake caliper bracket
Crack/damage 

 Replace.

EAM30033

ASSEMBLING THE FRONT BRAKE CALIPER

WARNING

EWA19230

• Before installation, clean and lubricate the

internal parts. Use new brake fluid for

2

1

2

2

1

1

3

Summary of Contents for WR250F 2022





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250F 2022

Caberg PRO SPEAK EVO Assembly preview
PRO SPEAK EVO
Brand: Caberg Pages: 3
Caberg just speak Quick Start Manual preview
just speak
Brand: Caberg Pages: 2
hepco & becker 6616519 01 01 Quick Manual preview
6616519 01 01
Brand: hepco & becker Pages: 4
APRILIA SHIVER 750 - Manual preview
SHIVER 750 -
Brand: APRILIA Pages: 163
Dakota Digital MCL-30K-SPD Installation Manual preview
MCL-30K-SPD
Brand: Dakota Digital Pages: 7
METRAKIT MINI50 GP 2009 Owner'S Manual preview
MINI50 GP 2009
Brand: METRAKIT Pages: 53
hepco & becker Easyrack 6617501 01 01 Manual preview
Easyrack 6617501 01 01
Brand: hepco & becker Pages: 4
R&G ECC0363R Fitting Instructions Manual preview
ECC0363R
Brand: R&G Pages: 6
Dennis Kirk Firstgear 512817 Manual preview
Firstgear 512817
Brand: Dennis Kirk Pages: 2
Cycle Protect The Liberator Installation & Owner'S Manual preview
The Liberator
Brand: Cycle Protect Pages: 15
Yamaha XV250P1 Owner'S Manual preview
XV250P1
Brand: Yamaha Pages: 98
Yamaha Star 2011 Owner'S Manual preview
Star 2011
Brand: Yamaha Pages: 108
Yamaha XVZ13TFY Owner'S Manual preview
XVZ13TFY
Brand: Yamaha Pages: 124
Yamaha ROAD STAR XV16A Owner'S Manual preview
ROAD STAR XV16A
Brand: Yamaha Pages: 117
Yamaha X MAX CZD300P 2022 Owner'S Manual preview
X MAX CZD300P 2022
Brand: Yamaha Pages: 142
Yamaha XVS13AW(C) Owner'S Manual preview
XVS13AW(C)
Brand: Yamaha Pages: 97
Yamaha V-star XVS650P Owner'S Manual preview
V-star XVS650P
Brand: Yamaha Pages: 119
Yamaha XVS650H 2016 Owner'S Manual preview
XVS650H 2016
Brand: Yamaha Pages: 96

Brands by name

Popular brands

Load more brands