Yamaha WR125R 2009 Service Manual Download Page 178

Page: 178 / 372

SWINGARM

4-65

EAS23350

REMOVING THE SWINGARM

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

2. Measure:

• Swingarm side play
• Swingarm vertical movement

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Measure the tightening torque of the pivot

shaft nut.

b. Measure the swingarm side play “A” by mov-

ing the swingarm from side to side.

c. If the swingarm side play is out of specifica-

tion, check the bushings and dust covers.

d. Check the swingarm vertical movement “B”

by moving the swingarm up and down.
If swingarm vertical movement is not smooth
or if there is binding, check the bushings and
dust covers.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS23360

CHECKING THE SWINGARM

1. Check:

• Swingarm

Bends/cracks/damage

→

Replace.

2. Check:

• Pivot shaft

Roll the pivot shaft on a flat surface.
Bends

→

Replace.

WARNING

EWA13770

Do not attempt to straighten a bent pivot
shaft.

3. Wash:

• Pivot shaft
• Dust covers
• Bushings

4. Check:

• Dust covers
• Bushings

Damage/wear

→

Replace.

EAS23380

INSTALLING THE SWINGARM

1. Lubricate:

• Spacer
• Oil seals
• Bushings
• Dust covers
• Pivot shaft

2. Install:

• Oil seals “1”

(to the swingarm)

Pivot shaft nut

80 Nm (8.0 m·kgf, 58 ft·lbf)

Swingarm end free play limit (axi-
al)

0 mm (0 in)

Recommended cleaning solvent

Kerosene

Recommended lubricant

Lithium-soap-based grease

Installed depth “a”

0 mm (0 in)

Summary of Contents for WR125R 2009





















































































































































































































































































































































































Search results

Summary of Contents for WR125R 2009

Reviews:

Brands by name

Popular brands

Yamaha WR125R 2009, Service Manual

Search results

Summary of Contents for WR125R 2009

Reviews:

Brands by name

Popular brands