manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 99 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 99

8-28

8

EBU24393

Checking the front brake lever free play 

The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever should have no
free play as shown. If there is free play, have a
Yamaha dealer check the brake system.

WARNING

EWB02471

Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:

●

Make sure the brakes operate smoothly and
that there is no free play.

●

Make sure the brakes do not drag.

●

Make sure the brakes are not spongy. All air
must be bled from the brake system.

Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.

EBU24513

Adjusting the brake pedal and rear 
brake lever free play and checking the 
brake pedal position 

The brake pedal and brake lever free play must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

TIP

●

Always perform this maintenance completely in
the following order whenever adjusting the rear
brake.

●

Before adjusting the brake lever and brake pedal
free play, check the rear brake shoes for wear.

1. Brake lever free play

U3D563E0.book  Page 28  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments