manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 93 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 93

8-22

8

WARNING

EWB02340

Do not start the engine when cleaning the
spark arrester, otherwise it could cause injury
to the eyes, burns, carbon monoxide poison-
ing, possibly leading to death, and start a fire.
Always let the exhaust system cool prior to
touching exhaust components.

EBU23920

V-belt cooling duct check hose 

If dust or water collects in the V-belt cooling duct
check hose, remove the hose and clean it.

EBU23930

V-belt case drain plug 

After riding in water deep enough to allow it to en-
ter the V-belt case, remove this plug to drain the
water from the case.

TIP

If water drains from the V-belt case after removing
the plug, have a Yamaha dealer check the ATV as
the water may affect other engine parts.

1. V-belt cooling duct check hose (left front side of ATV)

1. V-belt case drain plug

U3D563E0.book  Page 22  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments