manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 92 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 92

8-21

8

will affect carburetor jetting with subsequent
poor performance and possible engine over-
heating.

EBU27011

Cleaning the spark arrester 

Be sure the exhaust pipe and muffler are cool be-
fore cleaning the spark arrester.

1. Remove the tailpipe cover by removing the

bolts.

2. Remove the tailpipe by pulling it out of the

muffler.

3. Tap the tailpipe lightly, and then use a wire

brush to remove any carbon deposits from the
spark arrester portion of the tailpipe and inside
of the tailpipe housing.

4. Insert the tailpipe into the muffler and align the

bolt holes.

5. Install the tailpipe cover by installing the bolts,

and then tighten them to the specified torque.

1. Bolt

2. Tailpipe cover

1. Tailpipe
2. Spark arrester

Tightening torque:

Tailpipe bolt:

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

U3D563E0.book  Page 21  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments