manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 43 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 43

6-3

6

TIP

The engine is warm when it responds normally to
the throttle with the starter (choke) turned off.

EBU20291

Starting a warm engine 

Follow the same procedure as for starting a cold
engine, with the exception that the starter (choke)
is not required when the engine is warm. Instead,
start the engine with the throttle slightly open.

EBU20380

Operating the drive select lever and 
driving in reverse 

NOTICE

ECB00170

Before shifting, stop the ATV, otherwise the
transmission may be damaged.

Shifting: Forward

1. Bring the ATV to a complete stop.
2. Shift from neutral to forward and vice versa by

moving the drive select lever along the shift
guide.

TIP

Make sure that the drive select lever is completely
shifted into position.

3. Open the throttle lever gradually.

Shifting: Reverse

1. Bring the ATV to a complete stop.
2. Apply the brake pedal.

1. Drive select lever

2. F (Forward)

3. N (Neutral)
4. R (Reverse)

U3D563E0.book  Page 3  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments