manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 24 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 24

4-5

4

3. Tighten the locknut.

WARNING

EWB00240

Improper adjustment of the speed limiter and
throttle could cause throttle cable damage or
improper throttle operation. You could lose
control, have an accident or be injured. Do not
turn the adjusting screw out more than 12 mm
(0.47 in) or the throttle cable could be dam-
aged. Always make sure the throttle lever free
play is adjusted to 3.0–5.0 mm (0.12–0.20 in).
(See page 8-24.)

EBU18391

Front brake lever 

The front brake lever is located on the right handle-
bar. To apply the front brake, pull the brake lever
toward the handlebar grip.

EBU18442

Brake pedal and rear brake lever 

The brake pedal is located on the right side of the
ATV and the rear brake lever is located on the left
handlebar. To apply the rear brake, push down on
the brake pedal or pull the brake lever toward the
handlebar grip.

1. Locknut
2. Adjusting screw

3. No more than 12 mm (0.47 in)

1. Front brake lever

U3D563E0.book  Page 5  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments