manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 114 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 114

8-43

8

EBU25720

Troubleshooting 

Although Yamaha ATVs receive a thorough in-
spection before shipment from the factory, trouble
may occur during operation. Any problem in the fu-
el, compression, or ignition systems, for example,
can cause poor starting and loss of power.
The following troubleshooting chart represents a
quick and easy procedure for checking these vital
systems yourself. However, should your ATV re-
quire any repair, take it to a Yamaha dealer, whose
skilled technicians have the necessary tools, expe-
rience, and know-how to service the ATV properly.
Use only genuine Yamaha replacement parts. Im-
itation parts may look like Yamaha parts, but they
are often inferior, have a shorter service life and
can lead to expensive repair bills.

WARNING

EWB02280

Do not smoke when checking the fuel system.
Fuel can ignite or explode, causing severe inju-
ry or property damage. Make sure there are no
open flames or sparks in the area, including pi-
lot lights from water heaters or furnaces.

U3D563E0.book  Page 43  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments