Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 109

Page: 109 / 128

8-38

2. Remove the blown fuse, and then install a

new fuse of the specified amperage.

WARNING

EWB02171

Always use a fuse of the specified rating, and
never use a substitute object in place of the
proper fuse. An improper fuse or a substitute
object can cause damage to the electrical sys-
tem, which could lead to a fire.

3. Turn the key to “ON” and turn on the electrical

circuits to check if the devices operate.

4. If the fuse immediately blows again, have a

Yamaha dealer check the electrical system.

EBU25541

Replacing a headlight bulb

If a headlight bulb burns out, replace it as follows.

1. Remove the headlight bulb holder cover at the

rear of the headlight by pulling it off.

2. Remove the headlight bulb holder by pushing

it inward and turning it counterclockwise.

Specified fuses:

Main fuse:

20.0 A

Headlight fuse:

15.0 A

Ignition fuse:

15.0 A

Signaling system fuse:

10.0 A

1. Headlight bulb holder cover

U3D563E0.book Page 38 Monday, May 12, 2008 11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Search results

Summary of Contents for WOLVERINE 350 YFM35XY

Reviews:

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 109 / 128

Search results

Summary of Contents for WOLVERINE 350 YFM35XY

Reviews: