manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 103 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 103

8-32

8

EBU24230

Axle boots 

The axle boots must be checked for damage at the
intervals specified in the periodic maintenance and
lubrication chart. Check the axle boots for tears or
damage. If any damage is found, have them re-
placed by a Yamaha dealer.

EBU24752

Brake light switches 

The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.

1. Remove panel A. (See page 8-8.)

TIP

The brake light switch is properly adjusted when
the brake light comes on just before braking takes
effect.

2. Turn the brake light switch adjusting nut while

holding the brake light switch in place. To
make the brake light come on earlier, turn the

adjusting nut in direction (a). To make the
brake light come on later, turn the adjusting
nut in direction (b).

3. Install the panel.

EBU24900

Checking and lubricating the cables 

The operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.

1. Brake light switch
2. Brake light switch adjusting nut

U3D563E0.book  Page 32  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments