Yamaha WaveRunner VXS 2015 Owner'S/Operator'S Manual Download Page 54 | Manualshive

Page: 54 / 108

Yamaha WaveRunner VXS 2015 Owner'S/Operator'S Manual Download Page 54

Equipment operation

48

To close the glove compartment:
Push the lid down to securely lock it in place.

EJU37234

Watertight storage compartment

The watertight storage compartment is locat-
ed under the rear seat.
The compartment is watertight when the cap
is closed securely.
The watertight storage compartment is re-
movable.
To open the watertight storage compartment:
(1) Remove the rear seat. (See page 43 for

seat removal and installation proce-
dures.)

(2) Loosen the cap and remove it.

To close the watertight storage compart-
ment:
(1) Securely install the cap by tightening it

until it stops.

(2) Securely install the rear seat in its original

position.

EJU43790

Fire extinguisher holder and cover

The fire extinguisher holder and cover are lo-
cated in the bow storage compartment.

1

Watertight storage compartment cap

1

Watertight storage compartment

Watertight storage compartment:

Capacity:

5.8 L (1.5 US gal, 1.3 Imp.gal)

Load limit:

3.0 kg (7 lb)

1

1

UF2W70E0.book Page 48 Tuesday, December 8, 2015 9:03 AM

«
...
52
53
54
55
56
...
»

Summary of Contents for WaveRunner VXS 2015













































































































Reviews:

No comments