Yamaha WaveRunner VXS 2015 Page 89 Owner'S/Operator'S Manual Download

Page: 89 / 108

Care and storage

To store the battery:
(1) Clean the battery case using fresh water.
(2) If the battery terminals are dirty or cor-

roded, clean them using a wire brush.

(3) Apply Yamaha Marine Grease or

Yamaha Grease A to the battery termi-
nals.

(4) Store the battery in a cool, dry place.

NOTICE:

Storing the battery in an un-

charged condition can cause perma-
nent battery damage. Check the
battery periodically.

[ECJ00103]

To install the battery:
(1) Place the battery in the battery compart-

ment and hook the battery bands onto
the holders.

(2) Connect the positive (+) battery lead (red)

to the positive (+) battery terminal.

NOTICE:

Reversal of the battery leads

will damage the electrical parts.

[ECJ00262]

(3) Connect the negative (–) battery lead

(black) to the negative (–) battery termi-
nal.

(4) Connect the breather hose to the bat-

tery.

WARNING! Fire or explosion

could result if the breather hose is

damaged, obstructed, or not connect-
ed properly.

[EWJ00452]

(5) Make sure that the battery is securely

held in place.

Battery terminal

Recommended water-resistant grease:

Yamaha Marine Grease/Yamaha
Grease A

UF2W70E0.book Page 83 Tuesday, December 8, 2015 9:03 AM

Summary of Contents for WaveRunner VXS 2015













































































































Search results

Summary of Contents for WaveRunner VXS 2015

Reviews:

Related manuals for WaveRunner VXS 2015

Brands by name

Popular brands

Yamaha WaveRunner VXS 2015, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner VXS 2015

Reviews:

Related manuals for WaveRunner VXS 2015

Brands by name

Popular brands