background image

Operation

77

from objects—you need throttle to
steer.

NOTICE

ECJ01341

Never run the engine in water that is less
than 60 cm (2 ft) deep from the bottom of
the watercraft, otherwise pebbles or sand
could be sucked into the jet intake, caus-
ing impeller damage and engine overheat-
ing.

EJU43271

Starting off from a trailer

(1) Launch the watercraft.
(2) Attach the engine shut-off cord (lanyard)

to your left wrist, and then attach the clip
to the engine shut-off switch.

(3) Look in all directions, and then start the

engine.

(4) Squeeze the RiDE lever and move the

watercraft back slowly. (See page 31 for
RiDE lever operation procedures.)

EJU33114

Boarding and starting off from a dock

(1) Board the watercraft from the side.
(2) Attach the engine shut-off cord (lanyard)

to your left wrist, and then attach the clip
to the engine shut-off switch.

(3) Push the watercraft away from the dock,

grip the handlebars with both hands, and

place both feet on the floor of the foot-
well.

(4) Look in all directions, start the engine,

and then start off slowly.

EJU33236

Capsized watercraft

WARNING

EWJ00672

Improper uprighting can cause injury.

Be sure to shut the engine off by pulling
on the engine shut-off cord (lanyard) to
remove the clip from the engine shut-off
switch.

Do not put your hands in the intake
grate.

If the watercraft capsizes, turn it over imme-
diately.
To upright the watercraft:
(1) Remove the clip from the engine shut-off

switch.

(2) Swim to the rear of the watercraft. Turn

the watercraft over clockwise by pulling
on the ride plate with your left hand while
pushing down on the gunwale with your
right hand or foot.
If the port (left) side of the capsized wa-
tercraft is tilting up, push down on the
gunwale so that the port (left) side is
down before turning the watercraft
clockwise. 

NOTICE:

 Do not turn the

watercraft over counterclockwise,

UF2W70E0.book  Page 77  Tuesday, December 8, 2015  9:03 AM

Summary of Contents for WaveRunner VXS 2015













































































































Reviews: