manualshive.com logo in svg

Yamaha WaveRunner VX Sport 2014, Owner'S/Operator'S Manual, Page: 7 / 98

Share
Download
Yamaha WaveRunner VX Sport 2014 Owner'S/Operator'S Manual Download Page 7

General and important labels

1

EJU36452

Identification numbers

Record the Primary Identification (PRI-ID)
number, Craft Identification Number (CIN),
and engine serial number in the spaces pro-
vided for assistance when ordering spare
parts from a Yamaha dealer. Also record and
keep these ID numbers in a separate place in
case your watercraft is stolen.

EJU40501

Primary Identification (PRI-ID) number

The PRI-ID number is stamped on a plate at-
tached inside the engine compartment. (See
page 38 for seat removal and installation pro-
cedures.)

MODEL:

VX1100C-N (VX Sport)
VX1100B-N (VX Deluxe)
VX1100A-N (VX Cruiser)

EJU36551

Craft Identification Number (CIN)

The CIN is stamped on a plate attached to
the aft deck.

EJU30312

Engine serial number

The engine serial number is stamped on a
plate attached to the engine unit. (See page
38 for seat removal and installation proce-
dures.)

1

Primary Identification (PRI-ID) number loca-
tion

1

MODEL

F2P

F

PRI-I.D.

YAMAHA MOTOR CO., LTD. 
ASSEMBLED IN U.S.A. FROM AMERICAN AND JAPANESE
COMPONENTS.
ASSEMBLÉ AUX ÉTATS-UNIS DE PIÈCES AMÉRICAINES ET
JAPONAISES.

2 P

1

Craft Identification Number (CIN) location

1

Engine serial number location

1

1

UF2P71E0.book  Page 1  Wednesday, July 10, 2013  5:37 PM

Summary of Contents for WaveRunner VX Sport 2014



































































































Reviews:

No comments