manualshive.com logo in svg

Yamaha WaveRunner VX Sport 2014, Owner'S/Operator'S Manual, Page: 61 / 98

Share
Download
Yamaha WaveRunner VX Sport 2014 Owner'S/Operator'S Manual Download Page 61

Pre-operation checks

55

Operate the shift lever several times to make
sure that operation is smooth throughout the
whole range. Also, make sure that the reverse
gate moves up and down according to the
operation of the shift lever and that the gate
makes contact with the stoppers. (See page
30 for reverse system operation.)

EJU32595

Throttle lever checks

Operate the throttle lever several times to
make sure that operation is smooth through-
out the whole range. Also, make sure that the

throttle lever returns automatically to its fully
closed (idle) position when released.

Make sure that there is the proper amount of
throttle lever free play when the throttle lever
is in the fully closed (idle) position.

EJU40113

Remote control transmitter check 
(VX Deluxe / VX Cruiser)

Make sure that the remote control transmitter
operates properly. (See page 26 for Yamaha
Security System setting procedures and
page 31 for Low RPM Mode activation pro-
cedures.)

EJU32664

Engine shut-off cord (lanyard) check

Make sure that the engine shut-off cord (lan-
yard) is not damaged. If the cord is damaged,
replace it. 

WARNING! Never try to repair

1

Stopper

1

1

Throttle lever free play

Throttle lever free play:

4.0–7.0 mm (0.16–0.28 in)

1

UF2P71E0.book  Page 55  Wednesday, July 10, 2013  5:37 PM

Summary of Contents for WaveRunner VX Sport 2014



































































































Reviews:

No comments