Yamaha WaveRunner VX Cruiser 2007 Owner'S/Operator'S Manual Download | Manualshive

Page: 89 / 96

background image

Trouble recovery

82

EJU34620

Emergency procedures

EJU34630

Cleaning the jet intake and impeller

If weeds or debris get caught in the jet intake
or impeller, cavitation can occur, causing jet
thrust to decrease even though engine speed
rises. If this condition is allowed to continue,
the engine will overheat and may seize. If
there is any sign that the jet intake or impeller
is clogged with weeds or debris, return to
shore and check the intake and impeller. Al-
ways stop the engine before beaching the wa-
tercraft.

WARNING

EWJ00780

Before attempting to remove weeds or de-
bris from the jet intake or impeller area,
shut the engine off and remove the clip
from the engine shut-off switch. Severe in-
jury or death could result from coming in

contact with the rotating parts of the jet
pump.

CAUTION:

ECJ00650

If weeds or debris get caught in the jet in-
take, do not operate the watercraft above
trolling speed until they have been re-
moved.

(1) Turn the watercraft on its side as shown.

UF1K72E0.book Page 82 Wednesday, August 2, 2006 10:43 AM

«
...
87
88
89
90
91
...
»

Summary of Contents for WaveRunner VX Cruiser 2007

































































































Reviews:

No comments

Related manuals for WaveRunner VX Cruiser 2007

2270 CENTER CONSOLE

Brand: PURSUIT Pages: 104

Brand: Bestway Pages: 24

ALL-STAR 2101112

Brand: O'Brien Pages: 8

Samba Jeanneau Sun Odyssey 45 2007

Brand: Hermes Yachting Pages: 26

Brand: SEABOB Pages: 82

Brand: Scarab Pages: 182

Brand: elv Pages: 40

Brand: SeaDoo Pages: 801

Grand Banks 49' Classic

Brand: OceanFlyer Pages: 89

Brand: Lagoon Pages: 122

Brand: Mercury Pages: 64

Brand: Tayana Pages: 112

Brand: NW Explorations Pages: 58

Brand: Axis Pages: 216

Brand: Sea-doo Pages: 351

4-TEC series 2008

Brand: Sea-doo Pages: 555

2003 GTI LE RFI

Brand: Sea-doo Pages: 779

Brand: Rinker Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands