Yamaha WaveRunner VX Cruiser 2007 Owner'S/Operator'S Manual Download | Manualshive

Page: 55 / 96

background image

Operation

48

Make sure that the battery is securely held in
place.

EJU32540

Fire extinguisher

Check that there is a full fire extinguisher on
board.

The fire extinguisher holder and cover are lo-
cated in the front storage compartment.
To store the fire extinguisher, unhook the
band and remove the cover. Place the fire ex-
tinguisher in the holder, and then place the
cover over the fire extinguisher. Fasten the
cover and the fire extinguisher with the band
securely.

NOTE:

●

To check the fire extinguisher, see the in-
structions supplied by the fire extinguisher
manufacturer. Always keep the fire extin-

guisher secured in the holder with its cover
in place.

●

Always carry a fire extinguisher on board. A
fire extinguisher is not standard equipment
with this watercraft. If you do not have one,
contact a Yamaha dealer or a fire extin-
guisher dealer to obtain one meeting the
proper specifications.

EJU32590

Throttle lever

Check the throttle lever for proper operation.
Squeeze and release the throttle lever several
times to make sure that there is no hesitation
in its travel. It should be smooth over the com-
plete range and spring back to the idle posi-
tion when released.

WARNING

EWJ00490

Before starting the engine, always check
the operation of the throttle lever.

EJU32600

Steering system

Check the handlebars for looseness.
Turn the handlebars as far as possible to the
right and left to make sure that operation is
smooth and unrestricted throughout the
whole range. Also, make sure that the jet
thrust nozzle moves as the handlebars are

1

Fire extinguisher holder and cover

2

Band

UF1K72E0.book Page 48 Wednesday, August 2, 2006 10:43 AM

«
...
53
54
55
56
57
...
»

Summary of Contents for WaveRunner VX Cruiser 2007

































































































Reviews:

No comments

Related manuals for WaveRunner VX Cruiser 2007

Brand: Anacortes Yacht Charters Pages: 22

Brand: PURSUIT Pages: 136

SWIFT TRAWLER 42

Brand: BENETEAU Pages: 132

Brand: Lagoon Pages: 122

Brand: Navigator Pages: 26

Grand Soleil 40

Brand: Cantiere Del Pardo Pages: 97

RESPONSE TXi 2021

Brand: Malibu Boats Pages: 202

Brand: Yamaha Pages: 124

Brand: Lowell Pages: 2

Brand: Meridian Yachts Pages: 100

Brand: Sea Ray Pages: 68

Brand: Sea Ray Pages: 94

Brand: RowingSolutions Pages: 20

Brand: Marine Pages: 49

Brand: Hatteras Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands