manualshive.com logo in svg

Yamaha WaveRunner VX 700, Service Manual

Share
Download
Yamaha WaveRunner VX 700 Service Manual Download Page 67

4-18

1

2

3

4

5

6

7

8

9

A

Oil pump check

• If the oil delivery hoses are not full of oil,

fill them up.

• After installing the oil injection system,

bleed the system of any air.

1.

Clean the oil pump, and then check the
oil pump. Replace if damaged or worn.

Oil hose check

• If the oil delivery hoses are not full of oil,

fill them up.

• After installing the oil injection system,

bleed the system of any air.

1.

Check the oil hose and oil delivery hose.
Replace if cracked or damaged.

Check valve check

1.

Blow into the end 

a

 of the check valve,

and make sure that airflow from the end

b

 is unrestricted. Replace if the airflow is

restricted.

2.

Blow into the end 

b

 of the check valve,

and make sure that airflow from the end

a

 is restricted. Replace if the airflow is

unrestricted.

Oil pump air bleeding

Do not run the engine if oil does not flow
out of the air bleed screw. Inspect the oil
hose for proper routing and make sure
there are no restrictions in the line.

1.

Place rags around the air bleed screw 

1

to catch any oil that might spill.

2.

Fill the oil tank with the recommended oil.

TIP:

If the oil pump is replaced or the oil delivery
hose is reinstalled, bleed air from the hose by
disconnecting its from the oil pump.
After bleeding the air, reconnect the hose.

3.

Loosen the air bleed screw 

1

 two full

turns and make sure that both oil and air
bubbles flow out.

4.

When there are no air bubbles left,
tighten the air bleed screw.

5.

Wipe up any spilt oil.

Recommended engine oil:

YAMALUBE 2-W, or an equivalent 
NMMA-certified TC-W3 marine oil

Air bleed screw:

5 N·m (0.5 kgf·m, 3.7 ft·lb)

1

Oil pump

Summary of Contents for WaveRunner VX 700






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands