manualshive.com logo in svg

Yamaha WaveRunner VX 2015, Operator'S Manual, Page: 49 / 108

Share
Download
Yamaha WaveRunner VX 2015 Operator'S Manual Download Page 49

Instrument operation

43

If the engine is stopped after the check en-
gine warning is activated, the information dis-
play will indicate an error code.

If the check engine warning is activated, im-
mediately reduce the engine speed, return to
shore, and have a Yamaha dealer check the
engine.

EJU43740

Hour meter

The hour meter shows the total number of
hours that the engine has been running since
the watercraft was new.

TIP:

The elapsed time will be kept even if the bat-
tery terminals have been disconnected.

EJU43750

Voltmeter

The voltmeter shows the battery voltage.
When the battery voltage is normal, the volt-
meter displays approximately 12 volts.

If the battery voltage has dropped significant-
ly, “LO” is displayed on the voltmeter. If the
battery voltage has risen significantly, “HI” is
displayed. If “LO” or “HI” is displayed, imme-
diately return to shore and have a Yamaha
dealer service the watercraft.

1

Hour meter

1

1

Voltmeter

1

UF2X70E0.book  Page 43  Wednesday, September 17, 2014  8:52 AM

Summary of Contents for WaveRunner VX 2015













































































































Reviews:

No comments